|
Reflow Oven
| |
|
|
| |
Conceptronic Profile 117 Vintage 2001 |
|
| |
 |
|
| |
Description : |
|
| |
 Profile reflow ovens offer total gas management— from proprietary heating chambers with the highest linear convection ratio available, to filterless flux management and gas-to-gas cooling modules. Profile ovens offer unmatched heat transfer and thermal efficiency with virtually no maintenance required.
|
|
| |
For more info. location,picture,available or price send request to: info@getsmtglobal.com |
|
| |
|
|
| |
|
|
| |
Heller 11500W Reflow Oven Vintage 1997 |
|
| |
 |
|
| |
Description : |
|
| |
Left to Right board flow.
Rail and belt. We can upgrade for Lead Free
|
|
| |
For more info. location,picture,available or price send request to: info@getsmtglobal.com |
|
| |
|
|
| |
|
|
| |
Reflow Oven Furukawa XC B6 |
|
| |
Description : |
|
| |
Vintage:1994
Flow Direction: Right to Left.
|
|
| |
For more info. location,picture,available or price send request to: info@getsmtglobal.com |
|
| |
|
|
| |
|
|
| |
SENJU SPD II-300 Lead Free Flow Soldering Machine. |
|
| |
Description : |
|
| |
Vintage: 2005
Flow Direction: Left to Right.
PCB size: W: 50~300mm, L:100~350mm
Mixed soldering if chip/discrete component
Pass line height: 920mm
The entrance height is adjusted to the work conveyor height.
Wrap protection blade (entrance & exit)
Pre-heater (Far Infrared panel Heater)
Solder bath: Double wave system.
Spot cooler (up and down nozzles), air adjustment.
PCB angle setting: 5 degree
Pull out Solder Bath by rotary handle
Solder Capacity: 400kg
Entrance/ exit Conveyor.
Total length: 3494mm.
Condition: Very good working condition.
|
|
| |
For more info. location,picture,available or price send request to: info@getsmtglobal.com |
|
| |
|
|
| |
|
|
| |
VITRONICS Soltec XPM-VP-520 Reflow Oven |
|
| |
Description : |
|
| |
Stainless steel flat flex belt and edge rail
Type of mesh: 20x072 (.500inch pitch)
Chain pin leght:4.7/ .185 inches
Conveyor rails: hard anodized aluminium
Minium board width: 63.5 / 2.5 inches
Maximum board width: 508mm / 20 inches
Transport direction: Left to Right or Right to Left
Conveyor motor type: 130VDC gear motor
Conveyor speed range: 25-190cm/10-75inc. per minute
Accuracy: 12.7mm/0.5inc. per minute
Heat up power: 42 KVA
Runing Power: 10KVA
Voltage:400V
Cold start to warm up:<30 minutes
Maximum Temperature: 350*C
Temperature Control Accuracy:+/- 1*C
Heating Power per full zone:(@200V or 400V): 8KW
Heat zones top: 5
Heat zones bottem: 2
Cooling zones top only: 2
Top and Bottem Heaters: Forced ConvectionMotorized rail width adjust: standard
Vintage: 2003
|
|
| |
For more info. location,picture,available or price send request to: info@getsmtglobal.com |
|
| |
|
|
| |
|
|
| |
Tamura TAP40-437PM Reflow Oven. |
|
| |
Description : |
|
| |
Vintage:2004
Flow board: left to right
7 zones heaters
1 zone cooling
Auto width adjustment
Warp preventive unit.
Unintrerupted Power Supplay
Voltage: 208-220-480V.
Technical Support: Los Angeles and Portland, Oregon.
|
|
| |
For more info. location,picture,available or price send request to: info@getsmtglobal.com |
|
| |
|
|
|
